OpenWrt supports all major Wi-Fi_Alliance protocols including Wi-Fi_Protected_Access (WPA), the primary method of securing access to Wi-Fi.
Support for the latest WPA standards is dependent on your devices hardware and related Wi-Fi drivers.
Others include mixed and enterprise versions of WPA2 and WPA3, OWE, and OWE transition. For a full list of supported encryption types, see: basic#encryption_modes.
The configured encryption protocol is defined per network in the wifi-iface sections of the wireless configuration.
This can be configured in LuCI under Network -> Wireless -> click edit on each radio.
For Broadcom wireless chips use a proprietary driver that is generally not well supported in upstream Linux kernel. However it does work well enough for some targets and most use the newer mac80211 system.
For Atheros and mac80211 supported wireless chips, the wpad, hostapd or wpa_supplicant package is required.
The table below outlines the features supported by the packages and since which OpenWrt version they're available.
| Package | AP support | Client support | WPA Enterprise | OpenWrt Version |
|---|---|---|---|---|
| wpad | yes | yes | yes | 10.03+ |
| wpad-mini (recommended) | yes | yes | no | 10.03+ |
| hostapd | yes | no | yes | 7.06+ |
| hostapd-mini | yes | no | no | 8.09+ |
| wpa-supplicant | no | yes | yes | 7.06+ |
| wpa-supplicant-mini | no | yes | no | 8.09+ |
If not installed yet, choose the appropriate package for the desired configuration.
opkg update
opkg install wpad-mini
for x86 and ath10k
opkg update
opkg wpad-openssl
Configure WPA (PSK) encryption using UCI.
uci set wireless.@wifi-iface[0].encryption=psk
uci set wireless.@wifi-iface[0].key="your_password"
uci commit wireless
wifi
:!: The length must be between 8 and 63 characters. If the key length is 64 characters, it is treated as hex encoded.
Configure WPA2 (PSK) encryption using UCI.
uci set wireless.@wifi-iface[0].encryption=psk2
uci set wireless.@wifi-iface[0].key="your_password"
uci commit wireless
wifi
:!: The length must be between 8 and 63 characters. If the key length is 64 characters, it is treated as hex encoded.
:!: The default -mini packages for Atheros hardware will not work with Enterprise mode. (See the table above.)
The example below defines WPA2 Enterprise encryption in AP mode with authentication against an external RADIUS server at 192.168.1.200, port 1812.
uci set wireless.@wifi-iface[0].encryption=wpa2
uci set wireless.@wifi-iface[0].key="shared_secret"
uci set wireless.@wifi-iface[0].server=192.168.1.200
uci set wireless.@wifi-iface[0].port=1812
uci commit wireless
wifi
:!: The default -mini packages for Atheros hardware will not work with Enterprise mode. (See the table above.)
*Enter the following:
uci set wireless.@wifi-iface[0].encryption=wpa2
uci set wireless.@wifi-iface[0].mode="sta"
uci set wireless.@wifi-iface[0].ssid="SET_AS_NEEDED"
uci set wireless.@wifi-iface[0].encryption=wpa2+ccmp
uci set wireless.@wifi-iface[0].eap_type=peap
uci set wireless.@wifi-iface[0].auth=gtc
uci set wireless.@wifi-iface[0].identity="SET_AS_NEEDED"
uci commit wireless
wifi
*Modify the generated wpa_supplicant.conf file in the /var/run folder to remove the //password=""// line using your favorite editor.
*Enter the following:
wpa_cli -p /var/run/wpa_supplicant-wlan0
>status
*note the id of your interface (usually 0 in single interface systems)
*Enter the following at the wpa_cli prompt
>reconfigure
>reassociate
*When prompted for you OTP PIN enter the following at the wpa_cli prompt (if necessary replace the //0// with your desired interface id):
>otp 0 YOUR_PASSWORD_HERE
Do not use. This deprecated technology can be cracked in seconds with modern hardware. However some notes on how this works is below.
The format for the WEP key for the key1 option is HEX.
If you wish to use raw hex keys then you can skip to the UCI commands paragraph below. Raw hex keys have 10 hex digits (0..9, a..f) for 64-bit WEP keys and 26 hex digits for 128-bit WEP keys.
If you do not wish to use raw hex keys then follow the instructions below.
Generate a 64bit WEP key:
# echo -n 'awerf' | hexdump -e '5/1 "%02x" "\n"'
6177657266
Generate a 128bit WEP key:
# echo -n 'xdhdkkewioddd' | hexdump -e '13/1 "%02x" "\n"'
786468646b6b6577696f646464
Now use UCI to configure WEP encryption with the hex key you just generated.
uci set wireless.@wifi-iface[0].encryption=wep
uci set wireless.@wifi-iface[0].key1="786468646b6b6577696f646464"
uci set wireless.@wifi-iface[0].key=1
uci commit wireless
wifi
You can configure up to four WEP keys.